Hamburg, Illinois 62045
(618) 232-1139
(618) 232-1172 fax
| 51-411.036D | KEYLOCK ROUND MAINTAINED 2POS |
| 99-909.5 | FILM INSERT SINGLE GREEN |
| 99-909.4 | FILM INSERT SINBLE YELLOW |
| 96-901.0 | Lens no-recess for LED black 12,4x17,4 mom plastic opaque |
| 03-965.0 | BEZEL TRIM 03 SERIES 4S FLAT Front bezel black flat |
| 31-901.5 | Lens green flat 15.2x21.2 plastic translucent |
| 704-610.9 | Marking cap raised white D29 plastic translucent |
| 31-989.300 7E300 | KEY REPLACEMENT SERIES 22/31/51/61/99 DOM CODE 300 MASTER |
| 10-1109.1329 01-903.1 | Incandescent lamp T5,5 12V/100mA |
| 704-600.1 | TRIM RING ROUND ALUMINUM ANODIZED |
| 704-603.5 | Lens cap for indicator green D29 plastic transparent |
| 10-1120.1179 01-903.6 | Incandescent lamp T5,5 60V/20mA |
| 15-755.036 | KEYLOCK LL 1PST NO AU |
| 15-760.015 | KEYLOCK SNAP 1PDT DB AG |
| 15-760.025 | KEYLOCK SNAP 1PDT DB AU |
| 15-768.012 | KEYLOCK SNAP 1PDT DB .110QC AG |
| 15-768.022 | KEYLOCK SNAP 1PDT DB .110QC AU |
| 15-989.E170 | KEY REPLACEMENT SERIES 15 |
| 704-989.251 | KEY REPLACEMENT SERIES 04 704 |
| 31-989.351 7E351 | KEY REPLACEMENT SERIES 22/31/51/61/99 DOM CODE 351 |
| 10-5219.3125 02-963.45 | LED 6 CHIP T-6.8 48VDC 14MA GREEN |
| 61-9321.5 | Lens green flat 15,3x15,3 plastic transparent |
| 01-261.022 | Illuminated pushbutton main SA 1NC+1NO ST/PT 18x24 gold/silver |
| 52-928.0 | Rotating knob black D18 plastic opaque |
| 51-920 | Protective cover clear/black 25,5x20 |
| 02-904.1 | RESISTOR 10% 5W 3.3K OHM (125V) |
| 704-950.0 | LAMP HOLDER SCREW TERM (REPLACES 704-960.1) |
| 704-950.1 | LAMP HOLDER .250 QC (REPLACES 704-960.1) |
| 31-271.022 | Illuminated pushbutton main SA 1NC+1NO ST/PT D18 silver/gold |
| 31-906.2 31-902.2 31-903.2 | Lens red flat 15.2x21.2 plastic transparent |
| 704-611.4 | Lens raised yellow D29 plastic transparent |
| 704-074.3 | Switch Stop-actuator unlocking to twist release red D40 |
| 704-900.2 | Snap-action switching element SA 1NC screw silver |
| 10-1409.1329 700-000.1 | LAMP INCAND T 3-1/4 BAY 12V 100MA 1.2W |
| 01-272.025 | Illuminated pushbutton main SA 2NC+2NO ST D18 gold/silver |
| 01-131.025 | Illuminated pushbutton mom SA 1NC+1NO ST D18 gold/silver |
| 704-900.5 | Snap-action switching element SA 1NC+1NO screw silver |
| 10-1609.1289 11-903.1 | LAMP T1 B1-PIN12V/60MA11/19/99 (was 11-903.1/12) |
| 19-951.4 | Lens yellow 7,3x7,3 plastic translucent |
| 19-951.5 | Lens green 7,3x7,3 plastic translucent |
| 10-1424.1179 700-000.7 | Incandescent lamp Ba9s 130V/20mA |
| 31-810.005 | Buzzer ST 18x24 10-55VAC/10-75VDC |
| 704-950.5 | MOUNTING FLANGE PLASTIC (REPLACES 704-960.5 #4877) |
| 704-960.5 | MOUNTING FLANGE METAL/PLASTIC (USE 704-950.5) |
| 704-702.2 | Lens red 30x30 plastic transparent |
| 704-702.4 | Lens yellow 30x30 plastic transparent |
| 704-702.6 | Lens blue 30x30 plastic transparent |
| 704-709.7 | Lens holder clear 30x30 |
| 704-960.0 | LAMP HOLDER SCREW TERM REDUCTION RING/ BLACK ANODIZED |
| 704-900.1 | Snap-action switching element SA 1NO screw silver |
| 704-702.5 | Lens green 30x30 plastic transparent |
| 704-701.0 | Front bezel black 30x30 |
| 704-709.9 | Lens holder white 30x30 |
| 704-731.0 | Illuminated pushbutton-actuator black 30x30 |
| 704-732.0 | Illuminated pushbutton-actuator black 30x30 |
| 01-121.025 | Illuminated pushbutton mom SA 1NC+1NO ST 18x24 gold/silver |
| 01-261.025 | Illuminated pushbutton main SA 1NC+1NO ST 18x24 gold/silver |
| 01-972.6 | LENS RECT TPT W/CLR DIFF BLUE |
| 01-901.6 | Lens blue flat 12.8x18.8 plastic translucent |
| 31-041.006 | INDICATOR LIGHTED RECTANGULAR UNIV TERM |
| 704-502.0 | Selector switch-actuator 3 positions grey/black main-0-main short lever 30x30 |
| 704-510.0 | Selector switch-actuator 2 positions grey/black main short lever 30x30 |
| 31-263.025 | Illuminated pushbutton main SA 3NC+3NO ST 18x24 gold/silver |
| 01-901.9 | Lens white flat 12.8x18.8 plastic opaque |
| 01-982.2 | Lens red flat 12.8x18.8 plastic transparent |
| 01-982.4 | Lens yellow flat 12.8x18.8 plastic transparent |
| 01-982.6 | Lens blue flat 12.8x18.8 plastic transparent |
| 01-972.2 | Lens red flat 12.8x18.8 plastic transparent |
| 01-972.5 | Lens green flat 12.8x18.8 plastic transparent |
| 10-7123.2025 01-961.8 | LAMP T5.5 110V NEON GRN 01/14 (was 01-961.8) |
| 14-131.025 | Illuminated pushbutton mom SA 1NC+1NO ST D29 gold/silver |
| 704-600.0 | TRIM RING ROUND PLASTIC BLACK |
| 01-123.025 | Illuminated pushbutton mom SA 3NC+3NO ST 18x24 gold/silver |
| 97-450.037 | SWITCH SQ 1NO LL MOM |
| 97-430.037 | SWITCH RND 1NO LL MOM |
| 97-951.4 | LENS TPT SQUARE YELLOW |
| 97-951.5 | LENS TPT SQUARE GREEN |
| 97-951.9 | LENS TPT SQUARE WHITE |
| 97-931.2 | LENS ROUND TPT RED |
| 97-931.4 | LENS ROUND TPT YELLOW |
| 97-931.9 | LENS ROUND TPT WHITE |
| 98-843.021 EUS98-843.021 | LED 1-CHIP T-1 BI-PIN 2VDC 20MA RED |
| 98-843.051 EUS98-843.051 | LED 1-CHIP T-1 BI-PIN 2VDC 20MA GREEN |
| 704-611.2 | Lens raised red D29 plastic transparent |
| 704-632.1 | Illuminated maintained pushbutton-actuator grey D29 |
| 704-900.3 | Snap-action switching element SA 2NO screw silver |
| 10-1313.1249 31-963.2 | Incandescent lamp T1 3/4 MG 28V/40mA |
| 704-600.9 | Front ring D29 natural stainless steel |
| 704-614.4 | Mushroom-head cap yellow D40 plastic transparent |
| 704-702.7 | Lens clear 30x30 plastic transparent |
| 704-702.3 | Lens orange 30x30 plastic transparent |
| 704-703.4 | Lens cap square yellow 30x30 plastic transparent |
| 704-708.9 | Diffusor cap for lens cap white 30x30 |
| 51-972.022 | SWITCH BLOCK 2 ELEMENTS |
| 704-905.1 | Snap-action switching element SA 1NO PT6,3 silver |
| 704-905.2 | Snap-action switching element SA 1NC PT6,3 silver |
| 704-905.4 | Snap-action switching element SA 2NC PT6,3 silver |
| 704-905.5 | Snap-action switching element SA 1NC+1NO PT6,3 silver |
| 704-600.6 | Front ring D29 light grey plastic |
| 704-600.7 | Front ring raised D29 light grey plastic |
| 704-604.2 | Mushroom-head cap red D40 plastic opaque |
| 704-609.7 | Ribbed marking plate clear D29 plastic transparent |
| 704-631.1 | Illuminated momentary pushbutton-actuator grey D29 |
| 704-961.0 | TERMINAL QUICK CONNECT .250 TAB |
| 02-905 | TOOL LENS REMOVER SERIES 01 02F 03F 30 31 41 51 |
| 02-906 | TOOL LAMP REMOVER SERIES 01 02 03 14 30 31 41 51 52 |
| 19-910 | TOOL LENS REMOVER SERIES 19 |
| 10-1412.1279 700-000.2 | Incandescent lamp Ba9s 24V/50mA |
| 704-603.2 | Lens cap for indicator red D29 plastic transparent |
| 704-608.7 | Marking cap for lens cap clear D29 plastic transparent |
| 704-960.1 | LAMP HOLDER |
| 10-1613.1189 11-903.4 | Incandescent lamp T1 Bi-Pin 28V/24mA |
| 19-905 | TOOL MOUNTING NUT WRENCH SERIES 18 19 |
| 61-1220.0 | Illuminated pushbutton-actuator main 18x18 |
| 97-927.2 | LENS FLAT MATTE RED |
| 97-927.4 | LENS FLAT MATTE YELLOW |
| 10-1112.1279 01-903.2 | LAMP INCAND T-5.5 SLIDE 24V 50MA 1.2W |
| 01-907 | TOOL MOUNTING NUT SERIES 01 31 32 51 52 61 85 |
| 92-971.0 | TOOL FLANGE REMOVAL SERIES 84 & 92 HOUSING DISASSEMBLY |
| 84-997 | TOOL MOUNTING NUT WRENCH SERIES 84 |
| 704-341.0 | Keylock switch-actuator 2 positions grey/natural main 30x30 C 251 |
| 10-1422.1179 700-000.6 | LAMP BA9 110V/2.4W 704 (was 700-0006) |
| 10-1309.1309 | Incandescent lamp T1 3/4 MG 12V/75mA |
| 01-132.025 | Illuminated pushbutton mom SA 2NC+2NO ST D18 gold/silver |
| 704-602.0 | LENS ROUND OPAQUE BLACK |
| 31-953.2 | Lens red flat 15.2x15.2 plastic transparent |
| 92-851.342 | Switching Element non-illuminated ST/PT 1NO PCB gold |
| 10-1406.1369 700-000.0 | LAMP INCAND T 3-1/4 BAY 6V 200MA 1.2W |
| 704-943.5 | Flasher element 24/24VDC 85mA screw |
| 51-901.2 | Lens red flat 15.2x21.2 plastic translucent |
| 61-1200.0 | Illuminated pushbutton-actuator flush mounting neutral main |
| 61-9933.0 | Front bezel-set, flush mounting pushbutton natural D25 aluminum |
| 99-909.6 | Colour foil single blue 18,6x18,6 |
| 704-075.2 | Switch Stop-actuator unlocking to twist release red D40 |
| 96-953.0 AR | KEY CAP MOM DBL WIDE ENG ALARM RESET |
| 96-953.0 TQ | KEY CAP MOM DBL WIDE ENG TRBL QUIET |
| 96-953.0 NGR | KEY CAP MOM DBL WIDE ENG NORMAL GAS RESET |
| 10-2602.3172E 98-843.022 | 1 Chip LED T1 Bi-Pin 11 mm red 2,2VDC/20mA |
| 10-2602.3175E 98-843.025 | 1 Chip LED T1 Bi-Pin 11 mm green 2,2VDC/20mA |
| 704-608.9 | Marking cap for lens cap white D29 plastic translucent |
| 19-952.7 | Lens colourless clear 7,3x7,3 plastic transparent |
| 30-947.0 730-947.0 | PANEL CLOSURE PLUG |
| 31-901.0 | Lens black flat 15.2x21.2 plastic opaque |
| 31-030.002 | INDICATOR ROUND BLACK QC |
| 31-925 | COVER PROTECTION SERIES 31 32 RECTANGULAR Protective cap 24x23,5 |
| 31-931.2 | Lens red flat D15.8 plastic translucent |
| 31-901.4 | Lens yellow flat 15.2x21.2 plastic translucent |
| 10-1119.1199 01-903.5 | LAMP INCAND T-5.5 SLIDE 48V 25MA 1.2W |
| 02-904.0 | RESISTOR 10% 5W 2.7K OHM (VDRP RSTR 110/60V |
| 02-913.1-2.7K 02-913.10 | TERMINAL BLOCK RESISTOR PANEL 5 UNIT 2.7K OHMS |
| 01-901.2 | Lens red flat 12.8x18.8 plastic translucent |
| 01-901.3 | Lens orange flat 12.8x18.8 plastic translucent |
| 01-901.4 | Lens yellow flat 12.8x18.8 plastic translucent |
| 01-901.5 | Lens green flat 12.8x18.8 plastic translucent |
| ITL-5258 | Switch Interlock 12 Positions 3 form "C" Mutual Blocking Momentary Rectangular Lighted |
| 704-600.4 | Front ring D29 chrom plated plastic |
| 31-945 | TERMINAL CRIMP .079 X .020 LL SW |
| 31-955.5 | Lens green flat 15.2x15.2 plastic transparent |
| 704-912.5 | Switching element slow-make T 1NC+1NO screw silver/palladium |
| 31-966.04 | LED 1-CHIP T 1-3/4 MG 2VDC YELLOW |
| 704-098.0 | ACTUATOR LH ROTARY 3POS MOM-OFF-MAINT (BOXED W/704-950.5) |
| 10-1310.1319 31-963.1 | Incandescent lamp T1 3/4 MG 14V/80mA |
| 704-642.0 | INDICATOR LESS LENS & DIFF & LAMP IND SLEEVE W/O RESISTOR |
| 704-910.2 | Switching element slow-make T 1NC screw silver |
| 704-910.4 | Switching element slow-make T 2NC screw silver |
| 704-910.5 | Switching element slow-make T 1NC+1NO screw silver |
| 03-625.011 | Illuminated pushbutton two-part main SA 2DC screw 24x48 silver |
| 03-902.9/9 | Lens white/white flat 17,6x37.6 plastic translucent |
| 61-0000.02 | Indicator flush mounting neutral ST/PT |
| 31-935.7 | Lens colourless clear flat D15.8 plastic transparent |
| 03-901.2 | Lens red flat 17,6x37.6 plastic translucent |
| 19-951.6 | Lens blue 7,3x7,3 plastic translucent |
| 704-732.1 | Illuminated pushbutton-actuator grey 30x30 |
| 31-131.025 | Illuminated pushbutton mom SA 1NC+1NO ST D18 gold/silver |
| 51-338.025D | Keylock switch 2 positions main SA 4NC+4NO ST D18 gold/silver C 311 |
| 704-731.1 | Illuminated pushbutton-actuator grey 30x30 |
| 704-701.6 | Front bezel grey 30x30 |
| 99-922.7 | Pressure plate single clear/matt concave 18,6x18,6 |
| 96-906.0 | Lens with 1 recess for LED black 12,4x17,4 main plastic opaque |
| 10-1320.1179 31-963.4 | Incandescent lamp T1 3/4 MG 60V/20mA |
| 02-901.2 | Lens red flat 17.6x25.6 plastic translucent |
| 14-271.022 | Illuminated pushbutton main SA 1NC+1NO ST/PT D29 gold/silver |
| 10-1319.1199 | Incandescent lamp T1 3/4 MG 48V/25mA |
| 704-703.7 | Lens cap square clear 30x30 plastic transparent |
| 31-952.2 | LENS SQUARE CONCAVE TLT W/TLT DIFF RED |
| 31-952.5 | LENS SQUARE CONCAVE TLT W/TLT DIFF GREEN |
| 99-901.9 | Lens single complete clear/white 18,6x18,6 flach |
| 99-481.837 99-481 | Illuminated pushbutton single main with point of pressure 19X19 LL 2NO PCB gold |
| 51-933.7 | Lens colourless clear flat D15.8 plastic transparent |
| 704-611.7 | LENS ROUND EXTENDED TRANSPARENT CLEAR Lens raised clear D29 plastic transparent |
| 704-096.0 | ACTUATOR ROT RND L LVR GRAY 3POS 45* W/704-950.5 3 positions grey/black main-0-mom long lever D29 |
| 01-951.4 | Lens yellow flat 12.8x12.8 plastic translucent |
| 01-951.6 | Lens blue flat 12.8x12.8 plastic translucent |
| 704-901.5 | Snap-action switching element SA 1NC+1NO screw gold/silver |
| 10-1416.1289 700-000.3 | Incandescent lamp Ba9s 36V/56mA |
| 31-901.6 | Lens blue flat 15.2x21.2 plastic translucent |
| 31-901.9 | Lens white flat 15.2x21.2 plastic translucent |
| 01-931.2 | Lens red flat D15.8 plastic translucent |
| 01-931.3 | Lens orange flat D15.8 plastic translucent |
| 01-931.5 | Lens green flat D15.8 plastic translucent |
| 01-931.6 | Lens blue flat D15.8 plastic translucent |
| 01-931.9 | Lens white flat D15.8 plastic opaque |
| AK-1607-N-BBW | KEYPAD 16 KEYPAD HEXIDECIMAL 0-9 A-D * # |
| 51-261.025 | Illuminated pushbutton main SA 1NC+1NO ST 18x24 gold/silver |
| 704-097.0 | Selector switch-actuator 3 positions natural/black main-0-mom long lever D29 |
| 704-120.0 | Keylock switch-actuator 2 positions natural main D29 B 251 |
| 19-940 | SOCKET CONNECTOR PCB SERIES 19 STRAIGHT PCB plug-in base axial black |
| 31-989.311B 311B 311 | KEY REPLACEMENT SERIES 22/31/51/61/99 DOM BRASS |
| 10-1307.1369 31-963.0 | Incandescent lamp T1 3/4 MG 6,3V/200mA |
| 51-423.036 | Illuminated pushbutton mom LL 1NC+1NO UT 18x24 gold |
| 10-5312.3132 31-968.22 | 6 Chips-Led T1 3/4 MG red 24VDC/12,5mA |
| 99-908.9 ENG CLEAR | LENS DIFFUSER WHITE SGL WIDTH (ENGRAVED CLEAR) |
| 51-265.0 | Illuminated pushbutton-actuator main 18x24 |
| 70-911.0 770-911.0 | KEY CAP W/LED HOLES CLEAR 13MM TALL Spacing cap 2 recess for LED clear D15 plastic translucent |
| 70-201.0 770-201.0 | SWITCH ELEMENT MODULE SPST MOMENTARY GLD Switching Element non-illuminated ST/PT 1NO PCB |
| 31-967.24 | LED 4-CHIP T 1-3/4 MG 24VDC YELLOW |
| 01-963.4 | LAMP INCAND T 1-3/4 BI-PIN 28V 40MA |
| 03-021.001 | Indicator screw 24x48 |
| 03-901.4 | Lens yellow flat 17,6x37.6 plastic translucent |
| 03-901.5 | Lens green flat 17,6x37.6 plastic translucent |
| 70-901.0 770-901.0 | KEY CAP W/O LED HOLES CLEAR 18.9MM TALL Spacing cap clear D15 plastic translucent |
| 704-413.0 | Selector switch-actuator 2 positions natural/black mom short lever D29 |
| 704-123.1 | Keylock switch-actuator 2 positions natural mom D29 A |
| 10-6409.3244 700-002.14 | LED 6 CHIP T 3-1/4 BAYO 12-15VDC 20MA YELLOW |
| 10-6412.3164 700-002.24 | LED 6 CHIP T 3-1/4 BAYO 24-28VDC 18MA YELLOW |
| 70-910.0 770-910.0 | KEY CAP W/LED HOLES CLEAR 9MM TALL |
| 31-948 | ADAPTOR PANEL CUT OUT RECT |
| 61-9830.2 | Terminal cover snap-action switching element |
| 61-928.18 | LENS OPAQUE RECT GRAY |
| 61-991.0 | ALIGNMENT INSERT 18 X 24 BEZEL |
| 09.03201.02 1K2 | SWITCH 1K2 SLIDE SP 2POS ST PINS STD RED GLD |
| 704-955.1 | ADAPTOR FLUSH MT 04/14 BRUSHED AL FRONT RING-RECESSED MOUNT Front bezel-set for flush mounting D35 natural D30,5 |
| 51-901.4 | Lens yellow flat 15.2x21.2 plastic translucent |
| 51-901.6 | Lens blue flat 15.2x21.2 plastic translucent |
| 51-901.9 | Lens white flat 15.2x21.2 plastic translucent |
| 61-8470.12 | Snap-action switching element SA 1NC+1NO ST/PT silver |
| 01-985.5 | Lens green flat 12.8x12.8 plastic transparent |
| 01-453.036 | SWITCH SQ MOM LL 1NO/1NC LIGHTED PUSHBUTTON SQUARE MOM BLK GD UNV LL |
| 10-5109.3205 01-968.15 | 6 Chips-Led T5,5 green 12VDC/25mA |
| 31-282.025 | Illuminated pushbutton main SA 2NC+2NO ST 18x18 silver/gold |
| 01-926 | Protective guard narrow ends bent upwards 18x24 |
| 01-927 | Protective guard broad sides bent upwards 18x24 |
| 44-950 | LEGEND PLATE E-STOP 22.5MM X 60MM BLANK YELLOW |
| 31-903.6 | Lens blue flat 15.2x21.2 plastic transparent |
| 31-903.7 | Lens colourless clear flat 15.2x21.2 plastic transparent |
| 704-122.1 | Keylock switch-actuator 2 positions natural main D29 B+C 252 |
| 704-122.2 | Keylock switch-actuator 2 positions natural main D29 B+C 253 |
| 01-975.5 | Lens green flat 12.8x12.8 plastic transparent |
| 97-927.7 | LENS FLAT MATTE CLEAR |
| 99-920.0 | Lens bezel single black 18,6x18,6 plastic opaque |
| 61-9642.2 | Lens flush mounting red D19,7 plastic transparent |
| 61-8420.12 | Snap-action switching element SA 2NO ST/PT silver |
| 84-9420 | TERMINAL .110 QC FOR SERIES 84 CABLE SHOE 2,8x0,8 |
| 704-945.0 | Enclosure 94x94x81, with mounting cut-out 1x+22,5, grey/yellow plastic |
| 61-9642.6 | Lens flush mounting blue D19,7 plastic transparent |
| 704-915.4 | Switching element slow-make T 2NC PT6,3 silver |
| 704-963.6 | Marking plate D60 yellow EMERGENCY STOP |
| 84-7111.600 | Lens blue D19,7 plastic transparent |
| 84-1101.0 | ACTUATOR FLUSH IP67 BLACK PLASTIC HOUSING Illuminated pushbutton-actuator black D25 plastic |
| 84-2101.0 | ACTUATOR FLUSH BLACK IP40 Illuminated pushbutton-actuator black D25 plastic |
| 84-8510.0020 | SWITCH ELEMENT IP67 W/QC TERM 1N.O. CONTACT Switching Element 1NO ST/PT gold |
| 61-852.012 | Snap-action switching element 3 positions SA 2NO ST/PT silver |
| 61-9930.4 | Front bezel-set, flush mounting silver 24x24 alu look |
| 14-958.8 | Front bezel-set, mushroom-head cap D50 |
| 61-3440.4/1 | ACTUATOR E-STOP W/ARROWS Switch emergency-stop-actuator unlocking to twist release D27 |
| 61-9930.0 | Front bezel-set, flush mounting black 24x24 plastic opaque |
| 61-843.022 | Snap-action switching element SA 3NO ST/PT gold/silver |
| 18-052.0052 | OBSOLETE - NEW PART# 18-051.0052L IND/ FLUSH MOUNT/ 24VDC-20MA/ RED |
| 11-905 | TOOL MOUNTING NUT WRENCH SERIES 11 & 21 |
| 51-235.025D #311 | Keylock switch 2 positions main SA 1NC+1NO ST D18 gold/silver A 311 |
| 51-405.036D #311 | Keylock switch 2 positions main LL 1NC+1NO UT 18x24 gold A 311 |
| 10-2J19.1049 | Single-Led T1 3/4 MG white diffuse 48V AC/DC 4mA/8mA with 1/2 bridge rectifier |
| 10-1214.1249 02-903.3 | Incandescent lamp T6,8 30V/40mA |
| 704-902.2 | Snap-action switching element SA 1NC screw silver/palladium |
| 51-137.025D KEY#311 | Keylock switch 2 positions main SA 3NC+3NO ST D18 gold/silver A+C 311 |
| 61-9671.5 | Lens flush mounting green 24x24 plastic transparent |
| 61-9936.0 | Front bezel-set for flush mounting Selector switch black 24x24 plastic opaque |
| 61-9671.7 | Lens flush mounting clear 24x24 plastic transparent |
| 704-902.4 | Snap-action switching element SA 2NC screw silver/palladium |
| 14-473.036 | Illuminated pushbutton main LL 1NC+1NO UT D29 gold |
| 01-050.005 | INDICATOR SQUARE BLK SLDR Indicator 18x18 ST |
| 704-600.3 | SEALED FRONT RING ALUM Protective front ring natural D29 alu |
| 11-274.825 | Illuminated pushbutton main SA 4NC+4NO ST D16 gold/silver |
| 61-8550.22 | Snap-action switching element 3 positions SA 2NC ST/PT gold/silver |
| 704-941.0 | Resistor bloc 230/130V 20mA screw |
| 52-475.036 | Selector switch 2 positions main LL 1NO UT D18 gold |
| 61-842.025 61-842.022 | Snap-action switching element SA 2NO ST/PT gold/silver |
| 61-9321.6 | Lens blue flat 15,3x15,3 plastic transparent |
| 52-433.036 | Selector switch 2 positions mom LL 1NC+1NO UT D18 gold |
| 19-481.035 | Illuminated pushbutton main LL 1NO ST/PT 9x9 gold |